RF Explorer

RF Explorer spectrum analyzer with USB port

The RF Explorer is a portable spectrum analyzer. The LC display with background light shows a section of the radio spectrum and the receivable signals. Signal strength is shown in dBm or dBµV. This way you can see available signals on chosen frequency range at a glance. This makes the RF Explorer a very useful measurement instrument as well a fast working bug hunter to find hidden transmitters easily.

The RF Explorer has a frequency range from 15 to 2700 Mhz covering all important radio ranges that are used for surveillance cameras, mini transmitters, WLAN, emergency services radio and many others. Two different antenna inputs for various frequency ranges allow for the use of specially adapted antennas that make the RF Explorer even more sensitive. Minimal sensitivity of the spectrum analyzer is -115dBm. A marker on the LC display indicates the level of the strongest signal automatically.

Center frequency and displayed spectrum are easily adjusted in the menu, as well which antenna input to use. The display can memorize and display received maximum values. This means you can leave the receiver unattended for a while and check later if a signal was received. A special Wifi mode allows for detailed monitoring of channels on 2.4Ghz WLAN.

The USB port of the RF Explorer is used to charge the internal Li-Ion battery (1000mAh) and to transfer data to a PC or MAC computer. With the help of freely available software the received signal spectrum can be displayed on the computer and saved for documentary purposes. The Software is open source, the USB port transfer protocol is documented, too. This makes the RF Explorer very open and perfect for hackers and hobbyists, who want to implement their own ideas. Also, firmware updates are applied via USB. The USB-Cable is not included.

  • Included in shipment:
  • RF Explorer spectrum analyzer
  • broadband telescopic equipment antennas
  • helical antenna for 2.4GHz
  • User manual (english)
  • protective bag

Specifications RF Explorer
Gamma di frequenze 15 — 2700 MHz
Sensitivity f typ. ± 10 ppm
Sensitivity level typ. ± 3 dBm
Resolution f min. Bandbreite/112 typ.
Resolution level 0.5 dBm typ.
Setting accuracy f 1 kHz
Broadband displayed 112 kHz — 600 MHz
Antenna jack 2x SMA
Antenna impedance 50 Ω
Display LCD with background light, 128x64 px
Dynamic range -115 — 0 dBm typ.
Noise floor -115 dBm typ.
Livello mass. ingresso +5 dBm
Peso 185 g
Dimension without antennas 113 x 70 x 25 mm
Ordine No.
RF-EXPLORER RF Explorer Spektrum-Analysator 239.00 € Ordina In magazzino, spedizione in 1 o 2 giorni.
RFE-NFAK RF Explorer Near Field Antenna Kit 119.00 € Ordina Nuovo In magazzino, spedizione in 1 o 2 giorni.
RFEXP-RUBBER Rubber Shield for RF-Explorer 14.40 € Ordina Non in magazzino, di nuovo disponibile en 30 giorni
RFEXP-HOLDER Stand for RF-Explorer 17.00 € Ordina In magazzino, spedizione in 1 o 2 giorni.
21005.03 Attenuator 3 dB, 1 Watt, SMA 24.50 € Ordina In magazzino, spedizione in 1 o 2 giorni.
21005.06 Attenuator 6 dB, 1 Watt, SMA 24.50 € Ordina In magazzino, spedizione in 1 o 2 giorni.
21005.10 Attenuator 10 dB, 1 Watt, SMA 24.50 € Ordina In magazzino, spedizione in 1 o 2 giorni.
21005.20 Attenuator 20 dB, 1 Watt, SMA 24.50 € Ordina In magazzino, spedizione in 1 o 2 giorni.
Info sui costi di spedizione

RF Explorer Spectrum Analyser with 6 GHz Band

RF Explorer Spectrum Analyser with additional 6 GHz band (4850 - 6100 MHz), especially for measurements in the ISM/Wifi range. Case and operation similar to the analyser mdoel above.

Dati tecnici RF Explorer 6GHz Combo
Gamma di frequenzes 15 – 2700 MHz 4850 – 6100 MHz
Frequency precision typ. ± 0.5 ppm typ. ± 10 ppm
Level accuracy typ. ± 3 dBm typ. ± 6 dBm
Displayed bandwidth 112 kHz – 600 MHz 2 MHz – 600 MHz
Display resolution 3 – 600 kHz 58 – 812 kHz
Dynamic range -110 – -10 dBm typ. -105 – -15 dBm typ.
Livello mass. ingresso +30 dBm +25 dBm
Noise floor -105 dBm typ.
Frequency setting accuracy 1 kHz
Antenna connectors 2x SMA
Impedance 50 Ω
Display backlit LCD, 128x64 px
Peso 225 g
Size without antennas 113 x 70 x 25 mm
  • Included in shipment
  • RF Explorer Spektrum-Analyser 6G Combo
  • Wideband telescopic antenna
  • Helical rubber antenna 2.4GHz
  • Helical rubber antenna 5.8GHz
  • Operating Manual english
  • Protective Bag
Ordine No.
RF-EXP-6G RF Explorer Spectrum Analysator 6GHz Combo 349.00 € Ordina In magazzino, spedizione in 1 o 2 giorni.
RFEXP-RUBBER Rubber Shield for RF-Explorer-6G 14.40 € Ordina Non in magazzino, di nuovo disponibile en 30 giorni
RFEXP-HOLDER Stand for RF-Explorer-6G 17.00 € Ordina In magazzino, spedizione in 1 o 2 giorni.
21005.03 Attenuator 3 dB, 1 Watt, SMA 24.50 € Ordina In magazzino, spedizione in 1 o 2 giorni.
21005.06 Attenuator 6 dB, 1 Watt, SMA 24.50 € Ordina In magazzino, spedizione in 1 o 2 giorni.
21005.10 Attenuator 10 dB, 1 Watt, SMA 24.50 € Ordina In magazzino, spedizione in 1 o 2 giorni.
21005.20 Attenuator 20 dB, 1 Watt, SMA 24.50 € Ordina In magazzino, spedizione in 1 o 2 giorni.
Info sui costi di spedizione

Video RF EXplorer

RF Explorer Signal Generator bis 6000 MHz

RF-Explorer Signal Generator

Finally an affordable Signal generator with a frequency range of up to 6 GHz becomes available. The RF-Explorer signal generator (RFE6GEN) is fully programmable and prodices signals between 23.4 and 6000 MHz, the output level ranges from -40 to 0dBm. The signal is produced either as a constant carrier (CW) or as a sweep signal between two corner frequencies. Due to the small size and built-in rechargeable battery the RF-Explorer Signal generator is extremely well suited for portable use in the field.

In conjunction with the RF Explorer Spectrum Analyzer and the free Windows software you can set up a full spectrum analyser. The signal generator is then used as a tracking generator for the specturm analyser to do four-pole measurements on cables, filters, amplifiers and much more. An open source version of the software is available on the website of the manufacturer. The connection to the computer is done via USB, the signal generator has a Mini-B USB socket. The serial control protocol is documented, enabling you to write your own software for special measurements tasks. The Windows client software works with Windows XP/Vista, Win7 and later, both 32- and 64-Bit versions.

Here is the suitable RF-Explorer Spectrum Analyser.

Dati tecnici RFE Signal Generator 6GHz
Gamma di frequenze 23.4 – 6000 MHz
Frequency Resolution 1 kHz
Frequency Stability 0.5 ppm
Temperature Range 0 – 45° C
Output Level -40 – -30dBm & -10 – 0 dBm (in 3 dB steps)
Precision of output level ±0.5 dB (normalised) oder ±3 dB (absolute)
HF Connector SMA, 50 Ω
Power Supply USB-'Mini', 5V
Misura 130 × 17 × 25 mm
Peso 185 gr
Ordine No.
RFE-GEN RF Explorer Signal Generator 6GHz 169.00 € Ordina In magazzino, spedizione in 1 o 2 giorni.
RFEXP-HOLDER Stand for RF-Explorer Signal Generator 17.00 € Ordina In magazzino, spedizione in 1 o 2 giorni.
40073.03 USB Cable 30cm, USB A/B-mini 2.90 € Ordina In magazzino, spedizione in 1 o 2 giorni.
40073.15 USB Cable 150cm, USB A/B-mini 3.90 € Ordina In magazzino, spedizione in 1 o 2 giorni.
21005.03 Attenuator 3 dB, 1 Watt, SMA 24.50 € Ordina In magazzino, spedizione in 1 o 2 giorni.
21005.06 Attenuator 6 dB, 1 Watt, SMA 24.50 € Ordina In magazzino, spedizione in 1 o 2 giorni.
21005.10 Attenuator 10 dB, 1 Watt, SMA 24.50 € Ordina In magazzino, spedizione in 1 o 2 giorni.
21005.20 Attenuator 20 dB, 1 Watt, SMA 24.50 € Ordina In magazzino, spedizione in 1 o 2 giorni.
Info sui costi di spedizione

RF-Explorer Analyser + Signal Generator bundled

RF-Explorer Spectrum Analyzer (the 3G version up to 2.7 GHz) and the RF-Explorer Signal Generator together in a bundle!
In conjunction with the freely available Windows software you get a fully programmable network analyser for automation purposes and other applications.

And you save 69,00 €!

Ordine No.
RF-BUNDLE RF Explorer Signal Generator + Analyzer 3G 359.00 € Ordina In magazzino, spedizione in 1 o 2 giorni.
Info sui costi di spedizione

RF-Explorer Modules for Raspberry-Pi and Arduino

RF-Explorer for Arduino

RF-Explorer Boards for IoT systems like Raspberry-Pi and Arduino for remote monitoring of RF systems.

The well known functions of the RF-Explorer spectrum analyser are now also available for highly popular platforms like the Raspberry-Pi single board computer and the Arduino automation boards. These systems offer many options to automate various tasks in measurement and production of RF equipment. But also a constant monitoring of remote operated radio systems becomes possible at very low cost. Monitor transmissions of a amateur radio repeater or look for sources of interference.

Boards are available for Raspberry-Pi and Arduino platforms (3.3 V only!). With the aid of freely available software libraries an integration into larger monitoring systems is very easily achieved, even with remote access over the internet. Other paltforms like Beagle Bone, teensy and others can be easily adopted, only a serial port (UART) is required for control of the RFE-IoT (Internet of Things) boards. The circuits offer the well known RF analytic functions of the RF-Explorer 3G, the frequency range covers 15 to 2700 MHz. The RFE-IOT boards are ready to use, just plug them on the respective board. Even a later change of platform is possble by exchanging a pin header. Due to the wide support of different platforms, you have the choice between more compute power (Raspberry-Pi) or low power consumption (Arduino Due). For measurement tasks which require remote networks access the Raspberry-Pi is recommended.

Dati tecnici RF-Explorer IOT
Raspberry-Pi
Arduino 3.3V
Gamma di frequenze 15 – 2700 MHz
Connettore SMA 50 Ω
Preamplificatore (LNA) Si
Attenuator Si 30dB
Risoluzione Amplitude 0.5 dB
Proporzioni dynamici -130 – +10 dBm
Potenza mass. (ingresso) +30 dBm
Noise floor (tip.) -120dBm (LNA)
Stabilità frequenze (tip.) ± 10 ppm
Stabilità ampiezza (tip.) ± 3 dBm
Risoluzione frequenze 1 kHz
Resolution Bandwidth (RBW) automatic, 3 – 600 kHz
Voltaggio 3.3 V
Potenza assorbita 100 – 500 mW
Ordine No.
RFE-ARDUINO RF-Explorer Board per Arduino (3.3V systems) 149.00 € Questo articolo non è più disponibile. Scusi.
RFE-RASPI RF-Explorer Board per Raspberry-Pi 149.00 € Questo articolo non è più disponibile. Scusi.
Info sui costi di spedizione

RF-Explorer for Raspberry-Pi
Please note that the RF-Explorer for Arduino mandates a 3.3V system, not 5V! Using the RFE-ARDUINO with a 5V Arduino or clone will destroy the module! The manufacturer suggests to use the "Arduino Due" platform for best results.

Accessories RF Explorer

Stand for RF-Explorer

Stand for RF-Explorer

Desktop-Stand for the RF-Explorer.
This stand is the ideal complement for the RF-Explorer even if the computer is connected via the USB port on the bottom. The stand is supplied as a kit (see picture).

Ordine No.
RFEXP-HOLDER Stand for RF-Explorer 17.00 € Ordina In magazzino, spedizione in 1 o 2 giorni.
Info sui costi di spedizione

Rubber armament for RF Explorer

Gummi Cover RF Explorer

Solid rubber shield for the RF Explorer Spectrum Analyser and the RF Explorer Signal generator. Protects the devices when used in the field. The rubber has cutouts for all controls and connectors.

Ordine No.
RFEXP-RUBBER Rubber Shield for RF Explorer 14.40 € Ordina Non in magazzino, di nuovo disponibile en 30 giorni
Info sui costi di spedizione

SMA Male/Female Adaptor

All RF connectors wear with use. The RF Explorer SMA ports are subject to minimal wear each time the connector interface is coupled and de-coupled with an antenna, a SMA cable, an attenuator or a RF device of any kind. If you repeat plug/unplug operations over the RF Explorer SMA port hundreds of times, the SMA port may underperform over time and exhibit undesired attenuation.

To protect the SMA port for frequent plug/unplug operations, you can use this adaptor and keep it directly attached to the RF Explorer port. Then you plug/unplug other RF devices into this adaptor, not the original SMA port. After hundreds of operations, if the adaptor wear and show attenuation or reliability problems, you can just replace it by a new one and always keep your original RF Explorer SMA port intact.

Ordine No.
42850 SMA Male/Female Adaptor 5.20 € Ordina In magazzino, spedizione in 1 o 2 giorni.
42854.01 Adapter SMA-Connector/BNC-Jack 7.80 € Ordina In magazzino, spedizione in 1 o 2 giorni.
42874 Adapter SMA-Connector/PL-Jack 6.10 € Ordina In magazzino, spedizione in 1 o 2 giorni.
42873 Adapter SMA-Connector/N-Jack 6.50 € Ordina In magazzino, spedizione in 1 o 2 giorni.
Info sui costi di spedizione

USB Cable for RF-Explorer

The RF Explorer devices are offered without USB cable included, so why not order a sutable cable right away? 30 or 150cm, USB 'A' connector to USB 'Mini-B' connector.

Ordine No.
40073.03 USB cable 30cm, USB A/B-mini 2.90 € Ordina In magazzino, spedizione in 1 o 2 giorni.
40073.15 USB cable 150cm, USB A/B-mini 3.90 € Ordina In magazzino, spedizione in 1 o 2 giorni.
Info sui costi di spedizione

LogPer Antenna 750 MHz to 11 GHz

LogPer 750 MHz - 11 GHz 60073 LogPer

Logarithmic-periodic antenna for the frequency range from 750 to 11000 MHz (11 GHz). Suitable for SDR with a large frequency span, for example the 'HackRF One'. Antenna for lab measurements, test equipment, wide range frequency monitoring etc. Comes with 50cm RG-316 cable with SMA connector. Other cable lengths and connector avaiable on request. Gain 5 to 11 dB, return loss -11 dB, size 190 x 157 mm, weight 70 g.


Ordine No.
60073 LogPer 750MHz - 11 GHz, SMA 45.00 € Ordina In magazzino, spedizione in 1 o 2 giorni.
Info sui costi di spedizione

RF Explorer Near Field Antenna Kit Nuovo

RFE-NFAK

RF Explorer Near Field Antenna Kit is a collection of high performance set of 4 antennas designed for the most demanding RF diagnosis tasks.

  • The set contains:
  • RFEAH-25 – 25mm H-Loop
  • RFEAH-15 – 15mm H-Loop
  • RFEAH-5 – 5mm H-Loop
  • RFEAE-10 – 10mm E-Field

The three magnetic H-Loop antennas are very sensitive, compact and easy to use antennas for all sort of radiation sources. As the antenna diameter gets shorter, the antenna increase spatial resolution at the cost of some sensitivity loss; you should select RFEAH-25 for best sensitivity with connectors, large ICs and isolated signal traces, whereas RFEAH-5 works best for very narrow selective work in a populated PCB with close-by signal traces. RFEAH-15 is a good in-between compromise.

The electric field RFEAE-10 is offers a remarkable spatial resolution to determine the exact component in the PCB causing a problem, no matter how small it is.

The low loss design of these antennas exhibits at least 10dB more sensitivity than other near field antennas in the market, at a much lower cost.
Compared with other near field antennas, RF Explorer are smaller and lighter, exactly what fits best when space is constrained in a PCB.

Included with the antenna is high quality semirigid RF cable; this cable works as the handler of the antenna. The big advantage of this approach: you can shape the cable the way you want for the antenna to be located exactly where you need it, in most cases with no need to hold it in your hand.

The RF cable is coupled with a fast, easy to use SMA Push-On adapter so the different antenna models can be easily plugged in/out as required for the task. There is no need to deal with SMA nuts, just plug-n-play antennas.

  • Features:
  • Robust calibrated near field low cost 3x H-Loop and 1x E-Field antenna
  • Can work with RF Explorer Spectrum Analyzer, Signal Generator and other RF instruments and devices
  • Easy to use, reliable to find interference sources with high accuracy and resolution
  • Can be used to detect hidden bugs and transmission sources with remarkable spatial resolution
  • Feasible to generate interferences with Signal Generator and confirm RF circuit sensitivity
  • Capable of pre-EMC compliance tests
  • Include semi-rigid RF cable with coupled Push-ON SMA for easy operation and antenna selection
  • Protected by custom-designed, wooden box case with quality foam protection inside.
  • High frequency RF SMA Male-Male cable included
  • SMA Push-On adapter included
  • RoHS compliant
Ordine No.
RFE-NFAK RF Explorer Near Field Antenna Kit 119.00 € Ordina In magazzino, spedizione in 1 o 2 giorni.
Info sui costi di spedizione