Yaesu Relaiskomponenten

Yaesu DR-2XE FM/C4FM Relais 2m / 70cm Neu

Yaesu DR-2XE Yaesu DR-2XE

Yaesu offers you the dual mode repeater DR-2XE for a smooth transition from traditional FM mode to digital C4FM modulation. This relay is capable of both operation modes, the automatic mode select (AMS) recognizes the signal as C4FM digital or conventional FM and then the DR-2XE repeater retransmits the signal using the preset communications mode. This makes operating in FM as well as C4FM with only one hardware system possible.

The DR-2XE relay is shipped as a professional 19" system, an external power supply (13.8V, 15A) is required. The repeater can be used on 2m (144-146MHz) and 70cm (430-440MHz) with two receivers simultaneously, also as crossband repeater, see below. Configuration is done very comfortably via a large, coloured touch display on the front. With that you can program 'Id' (call sign), transmission and receiving frequency, transmission power (5, 20 or 50W), CTCSS, squelch and the automatic modulation select (AMS). Frequencies can be adjusted in 5 or 6.25 kHz steps.

The device requires 13.8V, max. 15A for operation. The DC cable is included. The repeater has an internal loudspeaker for local checking, also a microphone can be plugged in for testing the transmitter.

The DR-2XE repeater has no diplexer built-in, this needs to be added externally. On the rear side there are four separate connectors for transmit and receive antennas (2x RX, 2x TX) available. The transmit power can be adjusted to 5, 20 or 50W. The repeater identifier can be transmitted via voice or CW output in adjustable time intervals to meet regulatory requirements for automatic operating units.

New functions of the DR-2XE

IMRS, Internet Multi-Site Repeater: To achieve an IP networking independant from the Wires-X system, each repeater equipped with the option LAN-01A interface can be configured with up to 100 IP adresses (IPv4) of connected partner repeater systems. With a suitable selection of Digital Group IDs it is possible to form larger networks of connected repeaters. Each participant can use a certain DG-ID to address a local or remote repeater, a group of repeaters or the entire network. This IMRS operation requires the optional LAN-01A interface. This type of network operation does not require any infrastructure - no central server, no DNS address resolution, it is only depending on the individual configuration of each DR-2XE repeater. This allows continued operation over large areas even when other systems fail. Note: You can operate the DR-2XE either with Wires-X networking using the optional HRI-200 interface, or the IMRS type networking with the optional LAN-01A interface. A simultaneous operation of both netwirking systems is not possible.

DR-2XE Rear DR-2XE Rear

2 Receivers: In contrast to the predecessor DR-1XE the new DR-2XE is equipped with two independant receivers (and one transmitter). This offers new modes of operation. You can use the secondary uplink frequency for emergency purposes only, for example for the operator to control the repeater in case of interference on the normal uplink. Or you operate both input frequencies at the same time in a 'first come, first serve' mode. Or you assign one frequency as priority which then overrides the input on the other frequency. You can even configure two separate transmit frequencies for each input, but only one signal can be transmitted at one time.

The already known Digital Group ID (DG-ID) system now offers more possibilities than before. For example end user devices can transmit certain telemetry data, or the signal level of the repeater. Repeaters which are connected with the IMRS system (see above) can be addressed by individual or group-wide DG-IDs. Please note that it might become necessary to upgrade your radio with the latest firmware to make use of the newer features.

Repeater groups with DG-ID Repeater groups with DG-ID

Overall the DR-2XE has be designed more robust. The larger heat sink and a selection of commercial grade components allows a continued operation over long periods of time with any service requirements.

  • Included in shipment with the DR-2XE is:
  • DR-2XE Repeater in 19" rack mount case
  • DC Cable
  • English Manual
  • SCU-20 PC-ACC Cable (USB)
Technische Daten DR-2XE
#Frequenzbereich 144-146 MHz, 430-440 MHz
Kanalraster 5/6.25 kHz
Impedanz 50 Ω
Stromversorgung 11.7 – 15.8 V DC
Stromverbrauch 1.5 A (RX)
13 A (50 W TX, 144 MHz)
14 A (50 W TX, 430 MHz)
Temperaturbereich -20 °C – +55°C
Maße 482 mm × 88 mm × 380 mm (B×H×T)
Gewicht 8.4 kg
Sender
Sendeleistung 5/20/50 W
Antennenanschlüsse 2 × N Buchse
F1D, F2D, F3E, F7W (4FSK, C4FM)
Nebenwellen-Unterdrückung > 60 dBc
Empfänger
Empfängerkonzept Doppel-Superhet
Zwischenfrequenz 1st: 47.25 MHz, 2nd: 450 kHz
Antennenanschlüsse 2 × N Buchse
Empfindlichkeit 0.3 µV (Digital 2 m/70 cm) BER 1%
0.2 µV (FM 2 m/70 cm) 12 dB SINAD
Nebenkanalunterdrückung > 65 dBc (typ., 20 kHz offset)
Trennschärfe FM 12 kHz/35 kHz (-6 dB/-60 dB)
Intermodulations-Produkte < 65 dB (typ., 20 / 40 kHz offset)
Max. Audio-Leistung 4 W (4ohm., THD 10%, 13.8 V)

DR-2XE System Fusion II – Installation Support Program

As with the predecessor Yaesu offers an incentive to the amateur radio community to purchase this repeater. With the DR-2XE there will be two levels of financial support:

  1. Purchase of a new DR-2XE: Here Yaesu offers an incentive of 300 € to the dealer, which we pass directly to the end customer. To use this incentive please order the product 'DR-2XE-PROMO'. At the same time of your order we need the filled out application form. With out this form we cannot offer the promotional price.

    or

  2. Purchase of a new DR-2XE and Return of a used DR-1XE (trade in): Here the end customer can benefit from the above mentioned incentive (300 €) plus he or she will get a 300 € cashback directly from Yaesu, if the returned DR-1XE is accepted. Prerequisite for participation and procedure for this incentive:
    • Purchase of a new DR-2XE
    • Return of a used DR-1XE to WiMo. Please ask for an RMA number before returning an goods!
    • Fill out and submit the application form together with your order at WiMo
    • WiMo will check the returned DR-1XE for function, completeness, original packaging (if possible) and signs of wear. If all is ok we will forward the used repeater to Yaesu UK.
    • Yaesu UK will also check DR-1XE, if all is ok the 300 € cashback will be transferred. For this to succeed the application form must be submitted with the SEPA bank information of the customer.
    • Please calculate a duration of 8 to 10 weeks for the entire process until the payout of the cashback amount.

This incentive program is limited until December 31., 2017. According to our experience it is to be expected that Yaesu will extend this program early 2018.

Best.Nr.
DR-2XE Yaesu System Fusion FM/C4FM Repeater 1499.00 € Kaufen Neu Am Lager, Versand in 1 – 2 Tagen.
DR-2XE-PROMO Yaesu System Fusion FM/C4FM Repeater Incentive Preis 1199.00 € Kaufen Neu Am Lager, Versand in 1 – 2 Tagen.
DR-2XE.LAN Yaesu LAN-01A Option 295.00 € Kaufen Neu Am Lager, Versand in 1 – 2 Tagen.
Preis inkl. MwSt. zzgl Versandkosten

Zubehör DR-2XE

Best.Nr.
CT-174 Datenkabel Mini-DIN 10pol-10pol 27.20 € Kaufen Am Lager, Versand in 1 – 2 Tagen.
CT-175 Datenkabel Mini-DIN 10pol-6pol 23.40 € Kaufen Am Lager, Versand in 1 – 2 Tagen.
FVS-2 YAESU Sprachmodul 24.50 € Kaufen Am Lager, Versand in 1 – 2 Tagen.
HRI-200 YAESU Internet Link Adapter 116.00 € Kaufen Am Lager, Versand in 1 – 2 Tagen.
MH-48A6J DTMF-Mikrofon 46.30 € Kaufen Am Lager, Versand in 1 – 2 Tagen.
Preis inkl. MwSt. zzgl Versandkosten

HRI-200 Internet Link Adapter

HRI-200

Mit dem HRI-200 können die Yaesu C4FM-Geräte wie der FTM-400, DR1XE oder der DR-2XE direkt über das Internet verbunden werden. Die benötigte Software für das Interface, sowie die je nach Gerät benötigten Kabel gehören zum Lieferumfang. Das HRI-200 kann 2 Transceiver gleichzeitig ansteuern und 4 Frequenzen überwachen.
Das HRI-200 Interface unterstützt den vollen Funktionsumfang von Wires-X wie die Vernetzung des Group Monitors, Lokale Infos, Notfallhilfe ...
Auch an älteren Geräten kann das HRI-200 eingesetzt werden. Hier wird das Interface dann nur im FM-Mode betrieben und über DTMF bedient und der Funktionsumfang ist deutlich eingeschränkt.

Die Verbindung zwischen dem HRI-200 und einem Computer wird lediglich durch das mitgelieferte USB-Kabel vorgenommen. Eine zusätzliche Stromversorgung etc. ist nicht notwendig. Die notwendige Routerkonfiguration kann die Software durch UPnP selbst im Router vornehmen.

  • Im Lieferumfang des HRI-200 enthalten:
  • HRI-200 Interface
  • Datenkabel Mini-DIN 10polig (CT-174)
  • Datenkabel Mini-DIN 6polig (CT-175)
  • Wires-X Software (CD)
  • Bedienungsanleitung (Englisch)
  • Garantiekarte
  • Systemvoraussetzungen für das HRI-200:
  • Betriebssystem: Windows Vista/7/8/8.1
  • Prozessor: min. 2GHz
  • Festplatte: min. 1GB freier Speicherplatz
  • RAM: min. 2GB
  • USB: Full-Speed USB (USB-2)
  • Bildschirmauflösung: min. 1366x768 oder mehr, 16bit oder mehr
  • LAN-Port: mind. 100MBit
  • Internetverbindung: mind. 8 Mbps oder schneller
Best.Nr.
HRI-200 Yaesu Internet Link Adapter 116.00 € Kaufen Am Lager, Versand in 1 – 2 Tagen.
CT-174 Datenkabel Mini-DIN 10pin-10pin 27.20 € Kaufen Am Lager, Versand in 1 – 2 Tagen.
CT-175 Datenkabel Mini-DIN 10pin-6pin 23.40 € Kaufen Am Lager, Versand in 1 – 2 Tagen.
Preis inkl. MwSt. zzgl Versandkosten