Transceiver de YAESU
Yaesu FTDX-3000D Shortwave/50MHz Transceiver from the upper class
The FT-DX3000D is the latest 100 W shortwave station transceiver from Yaesu in the row of the upper class. Proven technologies such as DSP and fast antenna tuner was also included in this unit. Furthermore the FT-DX3000D benefited from the eperience with the top modell transceivers FT-DX5000 and FT-DX9000. This transceiver will not only with his look the center of your table.
For the first time in this class at the Yaesu now a TFT diplay is built in on which you have in addition to the band assignment, all the transceiver settings in mind. In addition of this, is beside the display a separate frequency display. The large TFT display has a very good readability from different angles. The high contrast makes viewing a pleasure.
Besides the visual changes, inside this transceiver, special emphasis was put on the best performance. Also new is the direct USB connection, so that external hardware can be quickly connected to the transceiver. Firmware updates can be played so directly with a USB cable without additional adapters into the transceiver.
You are a friend of digital modes?
With the FTDX-3000D you can start using the USB connection immediately! You do not need any sound card interface, this transceiver has all required already on board. In addition to the audio (in / out) on this port can also be keyed the PTT (PTT button and FSK). The already known serial port can also be found on this transceiver in the form of the known 9-pin RS-232 connector again. Thus, an operation of the FT-DX3000D on the computer is no limit.
You know the problem with strong stations close to the own frequency? Yaesu has in the FT-DX3000D installed as standard two roofing filters. In addition to the 3 kHz filter for SSB operation, was also intended for the ambitious CW fan and for that they integrate a narrow filter with 600Hz. Optionally, you can install a 300Hz filter (not included).
3 antenna inputs of which one can be configured for receive only (not in operation on that input possible), leave nothing to be desired.
The known 32-bit IF DSP was also included in this transceiver. By simply pressing a button the IF shift will set the passband to narrower settings. Of course, the very useful features such as IF filtering Notch and DNR have also been incorporated here.
The FT DX3000D offers full 100 W output power at a 13.8 V power supply with a power consumption of max. 23A. The built-in speech processor in combination with the built-in equalizer also provides in SSB mode for a clear and precise modulation, which is not so easily ignored. The use of stand microphones with optional equalizer is no longer necessary.
El teclado FH-2 + MH-31B8 se incluye en el envío del FT-DX3000.
The DVS-6 is an optional board for installation in the transceiver. The DVS-6 is a voice recorder/keyer which allows to record and transmit 5 audio tracks, each up to 20 sec long. This is especially useful for a contest. The DVS-6 can be controlled via the front panel of the transceiver, but it is much more convenient to use the included FH-2 keyboard.
|FT-DX3000D||Yaesu FT-DX3000D shortwave transceiver||1699.00 €||Comprar||No disponible, lo tendremos el 10. Jan. 2018 ⓘ|
|99FREQ||Frequency Extension Please see note!||25.00 €||Comprar||Disponible, envio en 1 o 2 diás. ⓘ|
|Gastos de envió|
Accessoires for the FTDX-3000
For CW enthusiasts narrow filters are particularly important. For the FT-DX3000D we offer a special 300 Hz roofing filter.
µ-Tune Kits are external filters for the bands 160m, 80 + 40m and 30 + 20m. These filters work with a motor driven coil and achieve a very high Q, again increasing the strong signal handling capabilities of the transceiver. The bandfilters require some assembly before use. All required cables are included. Size 330 x 120 x 120mm, weight 2.6kg.
|MTU-160||µ-Tune Kit 160m||669.00 €||Comprar||Ya no disponible en almacen, solo disponible a petición del cliente. Tiempo de entrega 100 días. ⓘ|
|MTU-8040||µ-Tune Kit 80/40m||669.00 €||Comprar||Ya no disponible en almacen, solo disponible a petición del cliente. Tiempo de entrega 120 días. ⓘ|
|MTU-3020||µ-Tune Kit 30/20m||669.00 €||Comprar||Ya no disponible en almacen, solo disponible a petición del cliente. Tiempo de entrega 120 días. ⓘ|
|Gastos de envió|
Technical Data FT-DX3000D
|RX Frequency Range||30 kHz - 56 MHz (operating)|
|1.8 - 54 MHz (specified performance, Amateur bands only)|
|TX Frequency Ranges||1.8 - 54 MHz (Amateur bands only)|
|Frequency Stability||±0.05 ppm (after 1 minute @ -10 °C ~ +50 °C)|
|Operationg Temperature Range||-10 °C ~ +50 °C|
|Emission Modes||A1A (CW), A3E (AM), J3E (LSB, USB), F3E (FM),|
|F1B (RTTY), F1D (PACKET), F2D (PACKET)|
|Frequency Steps||1/10 Hz (SSB,CW, & AM), 100 Hz (FM)|
|50 Ω, unbalanced||16.7 - 150 Ω, unbalanced (1.8 - 29.7 MHz)|
|25 - 100 Ω, unbalanced (50 - 54 MHz)|
|(Tuner ON, 1,8 - 50 MHz Amateur Bands, TX only)|
|Power Consumption||Rx (no signal) 1,8 A|
|Rx (signal present) 2,1 A|
|Tx (100 W) 23 A|
|Supply Voltage||DC 13,8 V ±10% (Negative Ground)|
|Medidas (WxHxD)||365 x 115 x 312 mm w/o knob and connector|
|Peso (approx.)||10 kg|
|Power Output||5 - 100 Watt (CW, LSB, USB, FM, RTTY, PKT)|
|2 - 25 Watt (AM carrier)|
|Modulation Types||J3E (SSB): Balanced|
|A3E (AM): Low-Level (Early Stage)|
|F3E (FM): Variable Reactance|
|Desviacion max. (FM)||±5.0 kHz / ±2.5 kHz|
|Harmonic Radiation||Better than -60 dB (1.8 - 29.7 MHz Amateur bands: Harmonics)|
|Better than -50 dB (1.8 - 29.7 MHz Amateur bands: Others)|
|Better than -65 dB (50 MHz Amateur band)|
|SSB Carrier Suppression||At least 60 dB below peak output|
|Undesired Sideband Suppression||At least 60 dB below peak output|
|Audio Response (SSB)||Not more than -6 dB from 300 to 2700 Hz|
|3rd-order IMD||-31 dB @14 MHz, 100 watts PEP|
|Bandwidth||500 Hz (CW)|
|3.0 kHz (LSB, USB)|
|6.0 kHz (AM)|
|16 kHz (FM)|
|Microphone Impedance||600 Ω (200 to 10 k Ω|
|Circuit Type||Double-conversion Superheterodyne|
|Intermediate Frequencies||9 MHz/30 kHz (24 kHz for AM/FM)|
|Sensitivity||SSB (2.4 kHz, 10 dB S+N/N)|
|4 μV (0.5 - 1.8 MHz, IPO "ON")|
|0.16 μV (1.8 - 30 MHz, RF AMP2 "ON")|
|0.125 μV (50 - 54 MHz, RF AMP2 "ON")|
|AM (BW: 6 kHz, 10 dB S+N/N, 30 % modulation @400 Hz)|
|28 μV (0.5 - 1.8 MHz, IPO "ON")|
|2 μV (1.8 - 30 MHz, RF AMP2 "ON")|
|1 μV (50 - 54 MHz, RF AMP2 "ON")|
|FM (BW: 15 kHz, 12 dB SINAD)|
|0.5 μV (28 - 30 MHz, RF AMP2 "ON")|
|0.35 μV (50 - 54 MHz; ARF MP2 "ON")|
|There is no specification in frequency ranges not listed.|
|Selectivity (WIDTH: Center)||Mode||-6 dB||-60 dB|
|CW/RTTY/PKT||0.5 kHz or better||750 Hz or less|
|SSB||2.4 kHz or better||3.6 kHz or less|
|AM||6 kHz or better||15 kHz or less|
|FM||12 kHz or better||30 kHz or less|
|Image Rejection||70 dB or better (1.8 - 30 MHz amateur bands|
|60 dB or better (50 - 54 MHz Amateur band)|
|Potecia max. audio||2.5 W into 4 Ω with 10% THD|
|Audio Output Impedance||4 to 8 Ω (4 Ω nominal)|
|Conducted Radiation||Less than 4 nW|
Specifications are subject to change, in the interest of technical improvement, without notice or obligation, and are guaranteed only within the amateur bands.
Apertura de frecuenciasTen en cuenta que:
Todos los equipos ofrecidos por WiMo cubren normalmente solo las bandas de radioaficionados en emisión.
La apertura de frecuencias de un equipo (abrirlo en TX) se puede hacer a petición explicita del cliente.
Los equipos de radioaficionado normalmente no están pensados para usarlos fuera de las bandas de radioafición. En algunos casos, el amplificador final o los filtros de salida pueden dañarse al emitir fuera de banda. Y eso no lo cubre la garantia.
La garantia del fabricante puede también anularse en algunos casos.